1998 chevy s10 2.2 torque specs. What is the torque specs sequence for a 1998 Chevy S10 4 cylinder 2.2 engine 2019-04-15

1998 chevy s10 2.2 torque specs

2.2 General Motor Torque Specs

1998 chevy s10 2.2 torque specs

The The Chevrolet S10 is a compact truck manufactured by the General Motors Corporation. Posted on Sep 23, 2010 Here is a suggested updated torque spec for this engine's rocker arm bolts; Rocker arms Step one: Torque to 11 ft lbs then tighten an additional 90 degrees of bolt head rotation. DimensionsThe standard wheelbase measurement for Chevy S10 models is 9 feet long. Ours has two wires, and you can see that the colors don't match up. Main bearings installed in block. Torque the retaining bolts to 25 ft.

Next

Chevrolet S

1998 chevy s10 2.2 torque specs

The long cylinder head bolts required 22 foot-pounds of torque and a 75-degree rotation. The 2200 uses an iron block and aluminum 2-valve cylinder head. So, we removed the engine again, rebuilt it again, this time with cam bearings. Cylinder head bolts 140 ft-lbs. Originally, the line had regular cab, extended cab and blazer models. After 2000, the same bolt must be torqued to 5. Connect the fuel line, and evaporative canister fuel line.

Next

GM 2.2L

1998 chevy s10 2.2 torque specs

Started reading online, and found out that these 2. I bought the pistons, rings, bearings and oil pump from Rock Auto Prep - Block and crank back from machine shop. Intake manifold bolts 25-30 ft-lbs. The engine has to belch, before it makes room for more antifreeze. If the fan bearing is worn out, you will have to get the fan bracket from a Chevy dealer.

Next

What is the torque specs sequence for a 1998 Chevy S10 4 cylinder 2.2 engine

1998 chevy s10 2.2 torque specs

Next, install the cam using plenty of assembly oil. Make sure the dot on the crankshaft gear is pointing towards the center of the Camshaft gear bolt. The machine shop also changed the pistons on the rod for me, since they are press fit on the wrist pins. Bolts on pre-1995 models connecting the engine block to the transmission, receive 18 ft. Connecting rod bolts 40-45 ft-lbs. Foot Notes Foot Note - If you forget to unplug the oxygen sensor before removing the head, and you pull the wires out of the connector, this is how the wires are supposed to be connected. Harmonic damper bolts 70-90 ft-lbs.

Next

GM 2.2L

1998 chevy s10 2.2 torque specs

After 2000, the same bolt must be torqued to 5. Harmonic damper bolt 70-90 ft-lbs. Assemble - Check ring gap in cylinders. Front cover bolts 12-15 ft-lbs. One of the old lifters was pumping to much oil up the push rod.

Next

CHEVROLET S

1998 chevy s10 2.2 torque specs

The machine shop did a good job. I bought the Gasket Kit from Rock Auto Assemble - Install the cam sprocket, timing chain, and timing chain cover. The crankshaft was worn 0. Water pump and water inlet are aluminum, and will have to be removed if your machine shop is going to hot tank the engine. Pressure plate bolts 35 ft-lbs.

Next

General Motors 122 engine

1998 chevy s10 2.2 torque specs

Copper spray gasket has been applied to the cylinder head gasket area. A torque angle meter is required to do this properly and to specification. Connecting rod bolts 40-45 ft-lbs. Bolt the transmission dip stick tube and fuel line to the intake manifold. The wheelbase is the distance from the center of the front wheels to the center of the rear wheels. I used red gasket adhesive to stick a fel-pro gasket to the block, then black rtv at the corners and the bearing lips of the oil pan.

Next

GM 2.2L

1998 chevy s10 2.2 torque specs

For 406 and 427 Cylinder head bolts 80-90 ft-lbs. Make sure to bolt the heater tube to the valve cover. Year Engine Displacement Liters cc Cylinder Head Bolts Main Bearing Bolts A Rod Bearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Spark Plugs Drain Plug Intake Exhaust 2003 2. Under the core is a tray used to catch the leaking antifreeze and drain it out the firewall. In 2004, Chevrolet did away with with the various cab models and just produced one S-10 before discontinuing the entire line the next year.

Next

I need torque specs for 1998 chevy s10 2.2 litre 4 cyl

1998 chevy s10 2.2 torque specs

Assemble - Install antifreeze, and fire it up. This could have done a lot of damage! The blazer model was discontinued after 1994. When adjusting the alignment of a vehicle, it is absolutely necessary to ensure that the proper alignment specs are used not just for a particular model but also for the appropriate year. The long cylinder head bolts required 22 foot-pounds of torque and a 75-degree rotation. The oil pressure is 65 at an idle when cold, but drops to 20 at an idle after a hard run down the interstate. If your engine utilizes screw-in type rocker arm studs with positive stop shoulders, no valve lash adjustment is necessary or possible.

Next