Scott - 1978 model with country miles. Caution: Do not allow brake fluid to come into contact with Caution: painted parts of the motorcycle, because brake fluid Do not allow brake fluid to come into contact with. Caution: Make sure the cable is not at an angle, or its insula- tion may be damaged. Tightening torque: M 6 screw. The switch back to stage one as soon heating stage you have selected as the seat is warm. Engine temperature The column below the tem- perature symbol indicates the engine temperature. Note: Installed direction arrow of brake discs must be correct.
I searched high and low for a manual for my car and they no longer produce one, it is all handled by the diagnostics computer. Before riding off, always check that the brakes bite as soon as the brake lever is pulled or the brake pedal depressed. Note: Only loosen the threaded connections at the lower rear frame. The following values can be dis- played in panel 2: When the motorcycle is at a standstill the heat of the engine °C Ambient temperature can falsify ambient-temperature Range reading 1. Note: Mark the position of the brake disc. Some of the work calls for spe- cial tools and a thorough know- ledge of motorcycle technology. By the same token, the spring rate decreases when The static normal position is the sleeve allows the plastic.
Gear engaged and clutch not disengaged Select neutral or pull clutch lever Clutch pulled before ignition was switched on Switch on the ignition, then pull the clutch lever No fuel in tank. Make sure the lock is out of the way when you hook the helmet into position. Tightening torque: Fuel tank to rear frame. While every reasonable effort is made to ensure the accuracy of this data, we are not responsible for any errors or omissions contained on these pages. Encoding plug for Motronic 4. Centre the front-wheel stand Make sure the ground is level. Tightening torque: Big end bolts oiled Joint torque.
Slip the spacing bushing into. Engine switched off Normal operating position run Emergency off switch kill switch Grip heating Repeatedly press button 1 until the desired heating stage ap- with heated handlebar grips Operating the kill switch. Lights up yellow appears on Electronic immobiliser active the display Lights up yellow Flashes Fuel down to reserve Lights up yellow Appears on the dis- Engine in emergency-operation mode play Flashes red Appears on the dis-. Caution: When sliding the cover on, make sure that all cables are correctly located in their cable entries. The maximum The combination of spring mount, suspension and spring spring rate is achieved when the sleeve completely encloses the rate ensure that the suspension plastic element and rests on the geometry is always perfectly adjusted. If the brake or rear light The types of bulb fitted to fails, the symbol is accompan- your motorcycle are listed.
Dear All, Looking for a service manual for 2012 r1200r. Caution: The contact must be heard to engage and must be firmly located. Is a factory manual available? Caution: When removing cylinder, ensure that the piston does not strike the engine block. Caution: Do not scratch the surface of the leading link. The possible warnings are listed on the next page.
If you install the seat in the low position, check that the seat's rubber buffers 5 are in the bot- tom positions in mounts 6. At least the parts department at local dealerships didn't know about them recently when I asked them. Caution: Do not accidentally confuse rocker shafts and push- rods. Recharge General warning light shows forms self-diagnosis to ensure its the battery before you start the yellow. Push the connector away from the locking tab, do not lift or bend the locking tab.
Caution: Check installed positions of parts which have al- ready been run together. I am still looking forward to the arrival of my Haynes, but for now this has already identified a couple of parts that I wanted to find. Do not switch the ignition on for longer than absolutely Immediately after switching off necessary. Caution: Bleed the brake system carefully. Poly-V belt tensioning procedure: 1.
All pages are printable, just run off what you need and take it with you into the garage or workshop. Install the rear seat 76. If you need to fix something it provides step by step instructions for the exact car, parts numbers, torque specs the whole lot and it is automatically updated when new parts are released and new methods are required. . If the charge level is low, grip heating is switched kill switch off to ensure the battery's start- ing capability.